Topeak - Justin Foell

Full disclosure: I like Topeak’s bike rack products with their QuickTrack system. It started with the BabySeat, which both of my kids rode in, Then I bought the worlds most expensive milk crate for beer runs. But the most versatile attachment is the trunk bag.

Continue reading →

My only complaint about this trunk bag is the Made in China tag. Not because of the country of origin, but because of its placement. From day one of owning this bag, it was perfectly in the way of the zipper. You can see that mine has been “run over” by the zipper a number of times.

Despite the stupid tag, this thing has several useful compartments. Mesh zippered pockets on the sides where I keep sunscreen, lip balm, zip ties, and rain covers for shoes.

There’s a mesh pocket and elastic cords on the top for anything you want to have quick access to – or if you want to strap something down that is bigger than the bag.

Inside it’s one big compartment, but on the lid there’s another pocket inside. I keep a set of repair tools with a patch kit, and a couple maps of the local trail system.

On the back there’s a handle for easy carrying and even a place to mount a light (I keep my light mounted to the rack itself).

It securely locks into place with the trademark Topeak QuickTrack system, so I never worry about it flying off.

Case Study: RC Trunk

I write about radio control (RC) related stuff over at MeatballRacing.com and recently I found a YouTube channel called Berm Peak that also shares my enthusiasm for both bicycles and RC.

In this video he reviews a different Topeak trunk bag that has fold-out panniers.

He put in a 1:24-scale crawler, which is a perfect fit for these bags. Similarly, I put in my Jeep, the controller, some sunglasses and headed to the local nature center to do some crawling.

Elapsed Time	Moving Time	Distance	Average Speed	Max Speed	Elevation Gain	Calories Burned
01:13:37 hours	00:10:20 hours	1.04 mi.	6.04 mph	8.72 mph	61.35 ft.	118 kcal

Put the studded tires on and rode to a trail nearby for some snowshoeing

When when I got there, I switched to snowshoes for a hike.

Elapsed Time	Moving Time	Distance	Average Speed	Max Speed	Elevation Gain	Calories Burned
00:57:56 hours	00:13:30 hours	0.43 mi.	31:07 min/mile	12:46 min/mile	27.23 ft.	29 kcal

Went to Innsbruck Nature Center… Honestly didn't need snowshoes – the trail was already hard-packed from hikers. Was good to venture off of the trail however. Tested out my SCX24 RC Crawler 😎

I can’t fit the showshoes in the trunk bag, but I have a carrying solution for those I’ll share later.

I hiked to a good spot and played in the snow.

The trunk bag is indeed super versatile – I feel like every year I come up with another useful way to use it.

← Summary Only

I am not a gun nut, but this build was inspired by this comic and conversation:

@BillLindeke @Minneapolize maybe I can get my conceal & carry before open streets and show up like this pic.twitter.com/GLYFnwianM
— Justin Fœll (@justinfoell) June 19, 2013

Looking at it made me think that a similar, but more useful application of vertical bike rack storage, would be for fishing rods. Moore Lake is just down the hill from where I live, and it’s stocked with Bluegills and Bass 🎣

I made this fishing rod holder that attaches to my bike rack for less than $20, mostly from scraps I had in the garage. It holds four rods, but you could adjust it for as many as you’d like, as long as your bike rack setup will accommodate them.

Continue reading →

Materials

This is everything I used for this build:

1-1/4″ PVC Pipe – find a scrap piece to get it cheap
1-1/4″ PVC Coupling(s) – one for every rod you want to hold
Tube Strap(s) for 1 1/4″ PVC – one for every rod holder
PVC Primer & Cement
1/2″ thick plywood or fiberboard – I had a scrap laying around, you can get a small 2’x4′ project panel if you don’t have any scraps.
#10 x 1/2″ sheet metal screws
#10 x 3/4″ sheet metal screws
Steel sheet metal – I had a scrap laying around. It doesn’t need to be thick – it’s just used to stick to the bike rack magnet.
3D printed rack hooks – If you don’t have access to a 3D printer, comment below if you’d like me to make one and mail it

PVC Construction

I chose 1-1/4″ PVC because all of our rod handles will fit into that size pipe – you should test fit your thickest fishing rod before you buy.

I attached a PVC coupling to the pipe and then cut the pipe (with the coupling attached) using a hacksaw to 9 inches. This was both the size of my scrap wood and the size of the longest rod handle. You should go longer if your handles are longer than 9 inches.

To make a permanent connection, I used PVC primer and cement to bond the couplers to the pipes.

The couplers are there to serve as stops for the tubing straps – so they don’t fall through them.

To fasten the tube straps to the board I used #10 x 1/2″ sheet metal screws. I pre-drilled holes in the wood with a 1/8″ drill bit, then used a screwdriver on the screws.

I designed 3D printed hangers because I couldn’t find any readily available hooks that I liked at the hardware store. I like Topeak racks because of how their bag systems attach. I designed the hangars to conform to the Topeak’s 10mm rod construction – which I believe is a standard size for many bike racks.

To fasten the hangers to the board, I used #10 x 3/4″ sheet metal screws.

Backing and Hangars

The board I used was some leftover 1/2″ plywood. Mine was 9″ wide so I went with that – luckily that’s how long our rod handles are. You can cut the width to however many rods you want to hold. For my 4 rod holders it wound up being 15″x9″.

To make sure everything lines up well on the back, I used my Thule panniers as an example. The metal plate that sticks to the magnet is approximately 9″x4″ – so I cut a piece of sheet metal that size. You can use a hacksaw to (slowly) cut it. I used a cutting wheel to make quick work.

I also used the Thule pannier as a reference to gauge the placement of the metal backing position relative to the hangers so they’d be generally in the right place. It will ensure the steel plate is the right place so it will line up with the rack magnet without having to move it around on the rack.

I used 3/4″ screws to fasten the hangers, and 1/2″ screws to hold the steel plate. I pre-drilled the steel with a 3/16″ drill bit, and the wood with a 1/8″ one.

The hangers are 3D printed. If you don’t have access to a 3D printer, comment below and I’ll get in touch with you to send a set your way.

That’s it!

Gone Fishin’

There’s no provisions on this rack for bait and tackle, but you can use the opposite side of the rack for a pannier, or just put your bait and tackle in a backpack.

When I’m fishing while paddling, I keep a very small tackle box on the boat with me, and that is also perfect for local fishing by bike.

Usability tips

Riding around with 6-foot fishing poles is like riding around with a whip antenna – it’s real tall. Just beware of any low tunnels or doorways, tree branches, etc.

Also, you’re not going to be able to put a leg over the back like you normally would. A pole (and hooks) will prevent you from doing that. Be mindful while you’re getting on and off.

I (perhaps stupidly) tried out the purple worm seen in my tackle box above – set up as a Texas Rig. I felt some serious bites, but I didn’t land anything. In the end I’m lucky because I didn’t bring a net if I actually had caught a tenacious bass.

While I didn’t bring one, you could certainly put a net in one of the holders. This is more of a catch-and-release type of rig, and I wasn’t planning on any big bites my first time out, just a couple of sunfish 🐟

Want a set of 3D printed bike rack hangers for your DIY project? Comment below so we can connect!

← Summary Only

Milk crates were surely one of the first accessories ever strapped to a bicycle. It’s the simplest way to add significant carrying capacity to any bike. One of the first things I did when I got my bike was add a rack and a milk crate – but I wasn’t quite smart about it.

I wanted the crate to be removable, so rather than securing it with zip ties, I recycled some old tire tubes and inter-wove them with the rack and the holes in the crate. It seemed pretty solid, so I thought I’d make a trip to the liquor store. The problem with the tubes is they’re made of rubber, so they stretch. They stretch a little too much for a beer-laden milk crate.

When I got out of the saddle, rocking the bike ever so slightly was enough to stretch the tubes, and send my beers flying. I burst some Surly’s halfway home. Lesson learned.
Continue reading →

As you already know, I’m a fan of Topeak’s rack systems. They work great for carrying kids, groceries, panniers, etc. I’ve gone through a couple iterations of tail lights from Ax-Man Surplus that I usually just stick to the back of the rack with 3M Very High Bond (VHB) double-sided foam tape and some 3M adhesion promoter.

The foam tape, when used with adhesion promoter, works great for all bumps, jumps and falls. The cheap Ax-Man lights however, left something to be desired. One quit after some moisture got into the housing, the other quit because it was just plain cheap – I’d never paid more than $5 for any of them at Ax-Man.

Since I’d already invested over $100 in my front light, I figured it was time to give the back light some love. Continue reading →

Going to get some of these to do a review: Thule Commuter Pannier Set http://t.co/6liw3aLNLa @Commute_by_Bike

— Justin Fœll (@justinfoell) October 12, 2014

A year and a half after I purchased these bags, it’s time for a review. You can’t buy them anymore, but this is more of a review of panniers in general. I used to ride with a backpack. It works (and is good for laptop shock absorption), but be prepared to have an instantly sweaty back. I can’t walk up a flight of stairs with a backpack on and not start to feel damp 🙂 Getting the bag off of my back and on to the rack on my bike is a huge win for comfort and convenience.

Find your dirtbike #pressnomics pic.twitter.com/1mSA3MClZ5

— Justin Fœll (@justinfoell) January 22, 2015

Continue reading →

These Thule bags were a steal at $120 for the pair. Most decent panniers cost this much just for one! They were a deal because Thule discontinued this model. The replacement bag is a “unidirectional” one that can go on either the left or right side of the bike rack, whereas the ones I got are specifically made for left and right sides – they are slightly narrower towards the front of the bike.

The Thule bags have a pretty rad feature where you can “flip” and hide the rack attachment hardware and carry it as a normal-looking handbag, or add the included strap and wear it as a shoulder bag or backpack.

With my new job, I use one everyday to carry my laptop to work. The other bag, sadly sits idle most of the time as I only need one for what I’m carrying. They came as a pair and at the time of purchase I was thinking about all of the epic bike adventures I’d be going on, with both bags packed to the hilt. Carry all the things!

All The Things!

I will use both for something like another bike camping trip, but for day-to-day commuting, just one is great.

I have racks on both my road bike and my mountain bike (which is really more of a kid-hauler than a mountain bike). I like my Topeak racks because they have a secure mounting system and Topeak offers several attachments. The Thule panniers fit nicely on both of my racks despite their differing thickness of tubing. You cannot, however, attach a top mounted Topeak trunk bag and the panniers on the side at the same time – they interfere with each other. I plan on devising something that can go on the top while both panniers are on with some spare parts, but that will have to wait for later.

Carrying Laptops

100 years ago, when spinning hard drives in laptops were the norm, there were several creative ways to carry your laptop in a pannier. Solutions from suspension to excess padding were employed to ensure you didn’t jar the hard drive beyond its shock tolerance. I’ve gone the other way and simply purchased a laptop with a solid-state drive instead of a spinning disk. I lined the bottom of my panniers with a bit of bubble-wrap left over from a mailer, just to prevent any dents when I’m doing sweet jumps.

While the bags aren’t waterproof they come with a waterproof cover. I’ve only used the cover once (in a total downpour). Normally I can just ride home quickly in a sprinkle, because it’s only one mile to work 😎 The covers stow inside each bag and are easily added:

← Summary Only

Justin Foell

Technology, Bicycling, Hobbies, Kids, Life.

Tag Archives: Topeak

Carrying stuff by bike: trunk bag

Case Study: RC Trunk

Carrying stuff by bike: fishing rods

Materials

PVC Construction

Backing and Hangars

Gone Fishin’

Usability tips

Carrying stuff by bike: milk crate

Topeak TrolleyTote

Extra Features

Specialized Stix Comp Tail Light

Carrying stuff by bike: panniers

Carrying Laptops